Grab-on Flush Rail Slimline II Kit - 1255mm(W) X 1358mm(L) / C

This 1358mm/53.5” long, full-size, Slimline II cargo roof rack kit contains the Slimline II Tray, Wind Deflector and 2 pairs of Grab-On Flush Rail Feet to mount the Slimline II Tray to the roof rails of your vehicle. This system installs easily with off-road tough feet that grab on to the existing factory/OEM roof rails. No drilling required. \nAll Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. \nNOTE: Your vehicle must be equipped with the factory/OEM roof rails in order to use this rack kit. \nThis rack kit can be removed leaving your vehicle’s roof and roof rails in their original condition. \nFor a stronger expedition grade cargo carrying solution, Front Runner may offer a specific Foot Rail System to mount the Rack Tray to your vehicle. Front Runner Foot Rail solutions can be installed by removing the factory roof rails or used if no factory roof rails are fitted. \nFactory Rail Rack Kits are designed as a ''light duty'' cargo solution. Please refer to your vehicle's owner's manual for manufacturer's recommended load rating and do not exceed these limits. \nFor optimal load carrying capacity, we recommend that there is no cargo overhang (excludes sports gear) and all weight is distributed evenly across the rack. \nFactory Rail Rack Kits are not suited for extreme off-road conditions and therefore you should consider a different Front Runner mounting solution if this is your intended purpose. \nPlease contact us for advice on specific mounting solutions for your vehicle and use. \nAll Front Runner Racks are backed by a Limited Lifetime Warranty* \nNote: The load for Factory Rail Rack Kits must not exceed 110lbs or 50kg, and ensure the load is distributed evenly. \nNote: For specific load ratings and speed limitations refer to the detailed fitment guides.Note: A maximum driving speed of 130km/80mi per hour should be adhered to, when equipped with a Front Runner Roof Rack or Load Bar kit. KRGF011T - Grab-on Flush Rail Slimline II Kit - 1255mm(W) X 1358mm(L) / C \nConsisting of:2x GOFR008A - Dometic Grab-on Flush Rail Adaptor Plate (Pair)1x GOFR008L - Leopard Foot with Lock / Pair1x GOFR008N - Leopard Foot without Lock / Pair1x RRSTD07 - SLII Tray - 1255mm(W)X1358mm(L)1x WDST011 - Wind Deflector 20mm Lip Extra Narrow Pair /1165mm \nMaterial Used:Black epoxy powder - coated T6 aluminiumHigh strength steel \nApproximate Installed Weight: 22.87kg (50.42lbs) \nThe t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. \nTo determine the approximate height from your vehicle’s roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2'') to the height of the Foot or Grab-on Foot listed above. \nIf your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2'') to the height of the Legs to determine the height of the rack from your vehicle's rain gutters. \nIf your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2'') to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. \nShipping Dimensions:Width: 445mm (18'')Length: 1720mm (68'')Height: 320mm (13'') \nShipping Weight:Weight: 30kg (66lbs)